|
|
gmx grompp |
|
| Main Table of Contents | VERSION 5.0.7 | |
gmx grompp [-f [<.mdp>]] [-po [<.mdp>]] [-c [<.gro/.g96/...>]]
[-r [<.gro/.g96/...>]] [-rb [<.gro/.g96/...>]] [-n [<.ndx>]]
[-p [<.top>]] [-pp [<.top>]] [-o [<.tpr/.tpb/...>]]
[-t [<.trr/.cpt/...>]] [-e [<.edr>]] [-imd [<.gro>]]
[-ref [<.trr/.cpt/...>]] [-nice ] [-[no]v] [-time ]
[-[no]rmvsbds] [-maxwarn ] [-[no]zero] [-[no]renum]
gmx grompp uses the atom names from the topology file. The atom names in the coordinate file (option -c) are only read to generate warnings when they do not match the atom names in the topology. Note that the atom names are irrelevant for the simulation as only the atom types are used for generating interaction parameters.
gmx grompp uses a built-in preprocessor to resolve includes, macros, etc. The preprocessor supports the following keywords:
#ifdef VARIABLE
#ifndef VARIABLE
#else
#endif
#define VARIABLE
#undef VARIABLE
#include "filename"
#include <filename>
The functioning of these statements in your topology may be modulated by using the following two flags in your .mdp file:
define = -DVARIABLE1 -DVARIABLE2
include = -I/home/john/doe
For further information a C-programming textbook may help you out. Specifying the -pp flag will get the pre-processed topology file written out so that you can verify its contents.
When using position restraints a file with restraint coordinates can be supplied with -r, otherwise restraining will be done with respect to the conformation from the -c option. For free energy calculation the the coordinates for the B topology can be supplied with -rb, otherwise they will be equal to those of the A topology.
Starting coordinates can be read from trajectory with -t. The last frame with coordinates and velocities will be read, unless the -time option is used. Only if this information is absent will the coordinates in the -c file be used. Note that these velocities will not be used when gen_vel = yes in your .mdp file. An energy file can be supplied with -e to read Nose-Hoover and/or Parrinello-Rahman coupling variables.
gmx grompp can be used to restart simulations (preserving continuity) by supplying just a checkpoint file with -t. However, for simply changing the number of run steps to extend a run, using gmx convert-tpr is more convenient than gmx grompp. You then supply the old checkpoint file directly to gmx mdrun with -cpi. If you wish to change the ensemble or things like output frequency, then supplying the checkpoint file to gmx grompp with -t along with a new .mdp file with -f is the recommended procedure. Actually preserving the ensemble (if possible) still requires passing the checkpoint file to gmx mdrun -cpi.
By default, all bonded interactions which have constant energy due to virtual site constructions will be removed. If this constant energy is not zero, this will result in a shift in the total energy. All bonded interactions can be kept by turning off -rmvsbds. Additionally, all constraints for distances which will be constant anyway because of virtual site constructions will be removed. If any constraints remain which involve virtual sites, a fatal error will result.
To verify your run input file, please take note of all warnings on the screen, and correct where necessary. Do also look at the contents of the mdout.mdp file; this contains comment lines, as well as the input that gmx grompp has read. If in doubt, you can start gmx grompp with the -debug option which will give you more information in a file called grompp.log (along with real debug info). You can see the contents of the run input file with the gmx dump program. gmx check can be used to compare the contents of two run input files.
The -maxwarn option can be used to override warnings printed by gmx grompp that otherwise halt output. In some cases, warnings are harmless, but usually they are not. The user is advised to carefully interpret the output messages before attempting to bypass them with this option.